Under 29 CFR 1910.212(a)(1), "one or more methods of machine guarding shall be provided to protect the operator and other employees in the machine area" from hazards "such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks." The section is titled "General requirements for all machines," and it sets no inspection interval. The interval sits in the next standard: 1910.219(p)(1) says all power-transmission equipment "shall be inspected at intervals not exceeding 60 days." This article covers what each rule requires, the seven-foot line that runs through 1910.219, what OSHA expects of a guard, and the point where removing one becomes a lockout job.
A note on scope: these are federal OSHA general industry rules in subpart O. Machines with their own standard, such as woodworking machinery (1910.213), abrasive wheels (1910.215), mills and calenders (1910.216), mechanical power presses (1910.217) and forging machines (1910.218), follow that standard first. States with OSHA-approved plans can set different requirements, and nothing here is legal advice.
What 1910.212 requires of every machine
The general rule has three parts.
- Guarding where there is a hazard. Paragraph (a)(1) names "barrier guards, two-hand tripping devices, electronic safety devices, etc." as examples. It does not prescribe one method; it requires that the hazard be guarded.
- Guards that stay put and do no harm. Under (a)(2), "guards shall be affixed to the machine where possible and secured elsewhere if for any reason attachment to the machine is not possible." The same paragraph adds: "The guard shall be such that it does not offer an accident hazard in itself."
- Machines that stay put. Under (b), "machines designed for a fixed location shall be securely anchored to prevent walking or moving."
Point of operation
Paragraph (a)(3)(i) defines the point of operation as "the area on a machine where work is actually performed upon the material being processed." Under (a)(3)(ii), where a machine's operation exposes an employee to injury, the point of operation "shall be guarded." The device must conform to any standard written for that machine. Where there is none, it "shall be so designed and constructed as to prevent the operator from having any part of his body in the danger zone during the operating cycle."
Push sticks and similar aids have a limited role. Paragraph (a)(3)(iii) says special handtools for placing and removing material "shall not be in lieu of other guarding required by this section, but can only be used to supplement protection provided."
Paragraph (a)(3)(iv) lists machines that "usually require point of operation guarding": guillotine cutters, shears, alligator shears, power presses, milling machines, power saws, jointers, portable power tools, and forming rolls and calenders. Portable tools also have their own rules in 1910.243; the hand and power tool inspection checklist covers them.
Drums and fan blades
Two hazards get their own sentences:
- Revolving drums, barrels and containers must be guarded "by an enclosure which is interlocked with the drive mechanism, so that the barrel, drum, or container cannot revolve unless the guard enclosure is in place" (a)(4).
- Fan blades: "When the periphery of the blades of a fan is less than seven (7) feet above the floor or working level, the blades shall be guarded," with openings "no larger than one-half (1/2) inch" (a)(5).
1910.219 covers mechanical power-transmission apparatus: flywheels, shafting, pulleys, belts, ropes and chains, gears and sprockets, clutches and couplings. Seven feet recurs throughout. Flywheels with any part "seven (7) feet or less above floor or platform" are guarded (b)(1), and so are exposed horizontal shafting (c)(2), pulleys (d)(1) and clutches with projecting parts (k)(1) at that height. Sprocket wheels and chains "shall be enclosed unless they are more than seven (7) feet above the floor or platform" (f)(3).
Some rules add their own measurements:
- Horizontal belts. Where both runs are seven feet or less from the floor, the guard extends at least 15 inches above the belt or to a standard height; where both runs are 42 inches or less from the floor, "the belt shall be fully enclosed" (e)(1)(i).
- Gears. A complete enclosure, a standard guard at least seven feet high extending six inches above the mesh point, or a band guard covering the face of the gear (f)(1). Hand-operated gears that stop when hand power is removed are exempt, though guarding them "is highly recommended" (f)(2).
- Projections. "All projecting keys, setscrews, and other projections in revolving parts shall be removed or made flush or guarded by metal cover" (h)(1).
- Damaged pulleys. "Pulleys with cracks, or pieces broken out of rims, shall not be used" (d)(3).
The guard itself has a specification. Guards are "rigidly braced every three (3) feet" of their height (o)(1). Guardrails are 42 inches high with a midrail and posts no more than eight feet apart, and toeboards are at least four inches high (o)(5). Wood guards are allowed only in certain industries and conditions (o)(2).
The 60-day inspection
Paragraph (p) holds the only inspection interval in these two standards. Under (p)(1), "all power-transmission equipment shall be inspected at intervals not exceeding 60 days and be kept in good working condition at all times." The rest of (p) says what good condition means:
- Shafting "kept in alignment, free from rust and excess oil or grease" (p)(2)(i), with static sparks "carefully considered" where explosive dusts or flammable vapors exist (p)(2)(ii).
- Bearings "kept in alignment and properly adjusted" (p)(3).
- Hangers inspected so that "all supporting bolts and screws are tight" (p)(4).
- Pulleys aligned "to prevent belts from running off" (p)(5).
- "Inspection shall be made of belts, lacings, and fasteners and such equipment kept in good repair" (p)(6)(ii).
- Machinery "oiled when not in motion, wherever possible," by oilers wearing "tight-fitting clothing" (p)(7).
For point-of-operation guards, 1910.212 sets no frequency. The machine guarding inspection checklist is set up for monthly checks and after any guard change. That is a working practice, not an OSHA figure.
What a good guard does
OSHA's machine guarding eTool lists minimum requirements for safeguards. They work well as inspection questions:
- Prevent contact between any part of the body and dangerous moving parts.
- Secure: workers "should not be able to easily remove or tamper with the safeguard."
- Protect from falling objects that could drop into moving parts.
- Create no new hazards, such as a shear point or a sharp edge.
- Create no interference: a guard that slows the job "might soon be overridden or disregarded."
- Allow safe lubrication, ideally without removing the guard.
The eTool also notes that awareness barriers "are not considered adequate when continual exposure to the hazard exists."
When guards come off
Guards come off for maintenance, and that is where the lockout standard begins. 1910.147(a)(2)(ii) says normal production operations fall under subpart O, not lockout. Servicing during production is covered by lockout if an employee must "remove or bypass a guard or other safety device," or place any part of the body at the point of operation or "where an associated danger zone exists during a machine operating cycle."
The exception is narrow: minor tool changes and adjustments that are "routine, repetitive, and integral to the use of the equipment for production," done "using alternative measures which provide effective protection."
The eTool is blunt about the maintenance crew: it "must never fail to replace the guards before the job is considered finished and the machine released from lockout." Its return-to-service steps begin with an inspection "to ensure that all guards and other safety devices are in place and functional." The rest of the energy control program is in lockout/tagout requirements.
Training
According to the eTool, operator training should cover the hazards of each machine, the safeguards and how they protect, how to use them, "how and under what circumstances safeguards can be removed, and by whom," when lockout is required, and what to do if a safeguard is damaged or missing. It calls for that training for new operators and maintenance or setup personnel, when new or altered safeguards are put in service, and when workers move to a new machine or operation.
Making it real
A guard can be in place on Monday and propped open by Wednesday. A yearly walk-through on paper cannot show which machine ran without its guard last week.
- Scan the machine, not the form. A QR code on the machine opens its record: the guarding checklist, open work orders and documents such as the manual.
- Record the name and time on every check. For drives under 1910.219, that is the 60-day record, machine by machine.
The same pattern applies to a site's other recurring checks: safety inspections that get done.
Quick summary
- 1910.212(a)(1): guard against point of operation, ingoing nip point, rotating part, and flying chip and spark hazards.
- 1910.212(a)(2)–(3): guards attached where possible and no hazard in themselves, keeping the operator's body out of the danger zone; hand tools only supplement.
- 1910.212(a)(5): fan blades under seven feet guarded, with openings no larger than half an inch.
- 1910.219: power-transmission parts seven feet or less from the floor guarded, and all power-transmission equipment inspected at intervals not exceeding 60 days.
- 1910.147: removing or bypassing a guard for servicing brings in lockout, unless the minor servicing exception applies.
If your sites run presses, conveyors and drives across several lines, see how Vardian handles safety inspections and corrective action: a scan at the machine, the guard check as a form, and a failed check that becomes a work order.