Safety

Hand and power tool inspection checklist

The before-use check of hand tools and portable power tools against OSHA 1910.242 and 1910.243: guards, switches that shut off when released, cords and air hoses, abrasive wheels and cracked saws, with a result that tags a defective tool out of service.

How often
Before use on each shift, and when a tool is issued or returned
Who
Tool user or tool crib attendant
Time
About 5 min
Items
22
Set it up in Vardian

Have your own paper version? A photo of it is enough for Vardian AI to draft the form. Photo-to-form →

Before you use it

  • OSHA 29 CFR 1910.242(a) makes each employer responsible for the safe condition of tools and equipment used by employees, including tools and equipment furnished by employees. Compressed air is not used for cleaning unless it is reduced to less than 30 psi, and then only with effective chip guarding and personal protective equipment (1910.242(b)).
  • Under 1910.243(a), portable circular saws with blades over 2 inches have guards above and below the base plate, and the lower guard returns automatically and instantly to cover the blade when the saw is withdrawn from the work. Hand-held drills, grinders and disc sanders over 2 inches, belt sanders, reciprocating saws and similar tools have a constant pressure switch, and a lock-on control only if one motion of the same finger turns the tool off. Belt sanders are guarded at each nip point, and all cracked saws are removed from service. Pneumatic tools that could eject the tool have a tool retainer, and air hose is designed for the pressure and service (1910.243(b)).
  • Portable abrasive wheels are used only with safety guards, apart from the exceptions in 1910.243(c)(1)(i), and on portable grinders the guard’s exposure angle does not exceed 180° (1910.243(c)(3)–(4)). Immediately before mounting, each wheel is closely inspected and sounded with a ring test, and the spindle speed is checked against the maximum operating speed marked on the wheel (1910.243(c)(5)(i)). Cord-and-plug tools are visually inspected before use on any shift and removed from service when damaged (1910.334(a)(2)).

Tool

  1. 1

    Scan the tool tag

    Checkpoint scan
  2. 2

    Tool ID or asset number

    Note
  3. 3

    Tool type

    Hand tool · Electric power tool · Battery power tool · Pneumatic tool · Abrasive wheel tool

    Choice

Condition

  1. 4

    Housing, handle and body free of cracks and loose or missing parts

    Pass / fail
  2. 5

    Hand tools: heads, jaws and cutting edges undamaged; handles tight and sound

    Pass / fail
  3. 6

    No cracked saw blades

    Pass / fail

Guards and controls

  1. 7

    Guards present, in place and undamaged

    Pass / fail
  2. 8

    Circular saw lower guard returns instantly to cover the blade

    Pass / fail
  3. 9

    Belt sander nip points and the unused run of the belt guarded

    Pass / fail
  4. 10

    Switch shuts the tool off when released; any lock-on turns off with one motion of the same finger

    Pass / fail
  5. 11

    Switch placed so the tool cannot start by accident

    Pass / fail

Power and air supply

  1. 12

    Cord, plug and strain relief undamaged; grounding pin present where fitted

    Pass / fail
  2. 13

    Battery and charger undamaged

    Pass / fail
  3. 14

    Air hose and couplings rated for the pressure and undamaged

    Pass / fail
  4. 15

    Tool retainer fitted on pneumatic tools that could eject the tool

    Pass / fail
  5. 16

    Air pressure at the tool

    Set the limits from the manufacturer’s manual and your normal operating range.

    Reading· psi

Abrasive wheels

  1. 17

    Wheel guard fitted, with the wheel exposed no more than 180°

    Pass / fail
  2. 18

    Wheel inspected and ring-tested before mounting

    Pass / fail
  3. 19

    Spindle speed

    Not above the maximum operating speed marked on the wheel.

    Reading· rpm

Result

  1. 20

    Result

    Fit for use · Tagged and removed from service

    Choice
  2. 21

    Photo of any defect

    Photo
  3. 22

    Inspected by

    Signature

Field types in this template

  • Checkpoint scan
  • Note
  • Choice
  • Pass / fail
  • Reading
  • Photo
  • Signature

In Vardian, readings are checked against their limits as they are entered, and photos and signatures attach to the check itself.

From the sheet to the round

Build a template as a Vardian form, and each line becomes a checkpoint that knows its limit.

Animation: a paper checklist line, compressor discharge pressure with a blank for the reading in bar, becomes a Vardian checkpoint with a limit of 7.0 to 8.5 bar. Scanning the compressor's NFC tag verifies the checkpoint, a reading of 9.1 bar is flagged out of range, and a work order is created from it.

Run this checklist on the round

We'll set it up in Vardian with your checkpoints and limits during a demo.