Under 29 CFR 1926.453(b)(2)(i), "lift controls shall be tested each day prior to use to determine that such controls are in safe working condition." The general industry rule, 29 CFR 1910.67(c)(2)(i), uses the same sentence. That is the only inspection interval either standard sets. OSHA's aerial lifts fact sheet fills in the rest: a pre-start inspection before each work shift and a check of the work zone. This article covers which machines the rules apply to, what the daily test and the pre-start inspection look at, the fall protection and power line rules, and what happens to a lift with a defect.
A note on scope: this is the federal OSHA construction standard and its general industry counterpart. Electric power line work also falls under 1910.269, whose (p)(1)(i) calls for a thorough visual inspection of critical safety components "before use on each shift." States with OSHA-approved plans can set different requirements, and nothing here is legal advice.
Which machines are aerial lifts
Paragraph (a)(1) of 1926.453 covers "vehicle-mounted aerial devices used to elevate personnel to job-sites above ground" and names five types: extensible boom platforms, aerial ladders, articulating boom platforms, vertical towers, and combinations of them. They may be "powered or manually operated," and count as aerial lifts "whether or not they are capable of rotating about a substantially vertical axis."
The definitions in 1910.67(a) make the types concrete. An articulating boom platform has "two or more hinged boom sections"; an extensible boom platform has "a telescopic or extensible boom"; a vertical tower raises "a platform in a substantially vertical axis." A vehicle is "any carrier that is not manually propelled." Both standards tie design to ANSI A92.2-1969, and allow a "field modified" lift only if the change "has been certified in writing by the manufacturer or by any other equivalent entity."
Scissor lifts are handled separately. OSHA's 2016 hazard alert Working Safely with Scissor Lifts says they "are different from aerial lifts because the lifting mechanism moves the work platform straight up and down." It calls for guardrails and lists the scaffold standards among the rules that apply, with 1926.454 for training. Those are covered in scaffold inspection requirements.
Two standards, almost the same text
The twelve numbered rules in 1926.453(b)(2) and 1910.67(c)(2) are mostly word for word. Three differences matter:
- Who may operate. Construction: "only authorized persons." General industry: "only trained persons."
- What the worker wears. Construction says "a body belt shall be worn and a lanyard attached to the boom or basket," with a note that since January 1, 1998, body belts "are not acceptable as part of a personal fall arrest system," though one is acceptable in a tethering or restraint system. General industry requires "a personal fall arrest or travel restraint system that meets the requirements in subpart I," attached to the boom or basket.
- Wheel chocks. Both require them on an incline; construction adds "provided they can be safely installed."
The daily control test
The standard says what to test, not how. Paragraph (b)(2)(ix) describes the controls: boom platforms "primarily designed as personnel carriers, shall have both platform (upper) and lower controls." Upper controls sit "in or beside the platform within easy reach of the operator," lower controls "shall provide for overriding the upper controls," and all of them "shall be plainly marked as to their function." A daily test that works the platform controls but never tries the lower override has skipped half the job.
The same paragraph sets a rule for whoever is on the ground: "lower level controls shall not be operated unless permission has been obtained from the employee in the lift, except in case of emergency."
The pre-start inspection
The fact sheet goes further. "Prior to each work shift," it says, "conduct a pre-start inspection to verify that the equipment and all its components are in safe operating condition," following the manufacturer's recommendations. It splits the list in two.
- Vehicle components: fluid levels and leaks, wheels and tires, battery and charger, lower-level controls, horn, gauges, lights and backup alarms, steering and brakes.
- Lift components: operating and emergency controls, personal protective devices, hydraulic, air, pneumatic, fuel and electrical systems, fiberglass and other insulating components, missing or unreadable placards and markings, fasteners and locking pins, cables and wiring harnesses, outriggers and stabilizers, loose or missing parts, and guardrail systems.
The manufacturer's manual adds the model's own items. The aerial lift and boom lift pre-use inspection checklist puts a walk-around with the key off, a function test of both control stations and emergency lowering, and a work area check on one page.
The work zone check
According to the fact sheet, "employers must assure that work zones are inspected for hazards and take corrective actions to eliminate such hazards before and during operation." The list: drop-offs, holes and unstable surfaces; slopes, ditches and bumps; debris and floor obstructions; low ceilings and other overhead obstructions; overhead power lines and communication cables; hazardous locations and atmospheres; high wind, ice and other severe weather; and other people working close by.
Setup belongs to the same check. Under (b)(2)(vii), "the brakes shall be set and when outriggers are used, they shall be positioned on pads or a solid surface," with wheel chocks on an incline.
Fall protection in the basket
Four of the twelve rules are about staying in the basket:
- (iii) "Belting off to an adjacent pole, structure, or equipment while working from an aerial lift shall not be permitted."
- (iv) Employees "shall always stand firmly on the floor of the basket, and shall not sit or climb on the edge of the basket or use planks, ladders, or other devices for a work position."
- (v) The belt or harness and a lanyard attached to the boom or basket, as above. The fact sheet adds: close the access gates.
- (x) "Climbers shall not be worn while performing work from an aerial lift."
The harness and lanyard need their own check before use: the fall protection harness inspection covers it.
Load, travel and stowing
Under (b)(2)(vi), "boom and basket load limits specified by the manufacturer shall not be exceeded." The fact sheet counts "the combined weight of the worker(s), tools and materials," and says not to use the lift as a crane.
Under (b)(2)(viii), "an aerial lift truck shall not be moved when the boom is elevated in a working position with men in the basket," except equipment designed for it. Before travel, (b)(2)(xii) requires the boom to be "inspected to see that it is properly cradled and outriggers are in stowed position."
Power lines
The general industry electrical rule gives the numbers, and 1910.67(b)(4) points to it. Under 1910.333(c)(3)(iii)(A), equipment "capable of having parts of its structure elevated near energized overhead lines shall be operated so that a clearance of 10 ft. (305 cm) is maintained," plus 4 inches for every 10 kV over 50 kV. In transit with the structure lowered, it may drop to 4 feet. An aerial lift "insulated for the voltage involved," worked by a qualified person, may come as close as Table S-5 allows. The fact sheet's advice for everyone: "treat all overhead power lines and communication cables as energized, and stay at least 10 feet (3 meters) away."
Under (b)(2)(xi), "the insulated portion of an aerial lift shall not be altered in any manner that might reduce its insulating value." The fact sheet's example: do not drill holes in the bucket.
Training
Construction limits operation to "authorized persons," and 1926.21(b)(2) requires employers to "instruct each employee in the recognition and avoidance of unsafe conditions." The fact sheet says training should cover electrical, fall and falling object hazards; correct operation, including load capacity; a demonstration of skills before operating on the job; "when and how to perform inspections"; and the manufacturer's requirements. It calls for retraining after an accident, when new hazards are found, when a different type of lift is used, and when a worker is seen operating one improperly.
What happens to a defect
Neither standard has a removal-from-service paragraph for aerial lifts. The fact sheet does: "Do not operate any aerial lift if any of these components are defective until it is repaired by a qualified person. Remove defective aerial lifts from service (tag out) until repairs are made."
Making it real
A paper sheet in the cab shows that someone checked one lift. It cannot show a supervisor which lifts were never tested this morning, or warn the next operator about a lift tagged at 6 a.m.
- Scan the lift, not the form. A QR code on the machine opens its record: the checklist, open work orders and documents such as the operator's manual.
- Record the name and time on every check. That answers "tested each day prior to use," lift by lift.
The same pattern applies to a site's other checks: safety inspections that get done. Forklifts follow a similar shift-start routine, covered in forklift inspection requirements.
Quick summary
- 1926.453(b)(2)(i) and 1910.67(c)(2)(i): lift controls tested each day before use, upper and lower, with the lower controls able to override.
- OSHA's fact sheet: a pre-start inspection before each work shift, following the manufacturer, and a work zone inspection before and during operation.
- Fall protection: feet on the basket floor, no belting off to nearby structures, a lanyard to the boom or basket; body belts are not acceptable for fall arrest.
- 1910.333(c)(3): at least 10 feet from energized overhead lines up to 50 kV, more above.
- Defective lifts are tagged out until a qualified person repairs them.
If your sites run boom lifts alongside forklifts and other mobile equipment, see how Vardian handles safety inspections and corrective action: a scan at the lift, the daily control test and pre-start items as a form, and a failed check that becomes a work order.